Standard of Practice

Strike First Inspections utilizes the following Standards of Practice

 

Part I. Definitions and Scope

These Standards of Practice provide guidelines for a real estate inspection and define certain terms relating to these inspections. Italicized words in these Standards are defined in Part IV, Glossary of Terms.

 

1. A real estate inspection is a survey and basic operation of the systems and components of a building which can be reached, entered, or viewed without difficulty, moving obstructions, or requiring any action which may result in damage to the property or personal injury to the Inspector. The purpose of the inspection is to provide the Client with information regarding the general condition of the building(s). Cosmetic and aesthetic conditions shall not be considered.

 

1. A real estate inspection report provides written documentation of material defects discovered in  the inspected building’s systems and components which, in the opinion of the Inspector, are safety hazards, are not functioning properly, or appear to be at the ends of their service lives. The report may include the Inspector's recommendations for correction or further evaluation.

 

1. Inspections performed in accordance with these Standards of Practice are not technically exhaustive and shall apply to the primary building and its associated primary parking structure.

​​

---------------------------------------------

 

Part II. Standards of Practice

A real estate inspection includes the readily accessible systems and components or a representative number of multiple similar components listed in Sections 1 through 9 subject to the limitations, exceptions, and exclusions in Part III.

​

SECTION 1 - Foundation, Basement, and Under-floor Areas

A. Items to be inspected:

1. Foundation system

2. Floor framing system

3. Under-floor ventilation

4. Foundation anchoring and cripple wall bracing

5. Wood separation from soil

6. Insulation

 

B. The Inspector is not required to:

1. Determine size, spacing, location, or adequacy of foundation bolting/bracing components or reinforcing systems

2. Determine the composition or energy rating of insulation materials

​​

---------------------------------------------

 

SECTION 2 - Exterior

A. Items to be inspected:

1. Surface grade directly adjacent to the buildings

2. Doors and windows

3. Attached decks, porches, patios, balconies, stairways and their enclosures, handrails and guardrails

4. Wall cladding and trim

5. Portions of walkways and driveways that are adjacent to the buildings

6. Pool or spa drowning prevention features, for the sole purpose of identifying which, if any, are present

 

B. The Inspector is not required to:

1. Inspect door or window screens, shutters, awnings, or security bars

2. Inspect fences or gates or operate automated door or gate openers or their safety devices

3. Use a ladder to inspect systems or components

4. Determine if any manufacturers' design standards or testing is met or if any drowning prevention safety feature of a pool or spa is installed properly or is adequate or effective. Test or operate any drowning prevention safety feature.

​​

---------------------------------------------

 

SECTION 3 - Roof Covering

A. Items to be inspected:

1. Covering

2. Drainage

3. Flashings

4. Penetrations

5. Skylights

 

B. The Inspector is not required to:

1. Walk on the roof surface if in the opinion of the Inspector there is risk of damage or a hazard to the Inspector

2. Warrant or certify that roof systems, coverings, or components are free from leakage

3. Inspect underground downspout diverter drainage pipes.

​​

---------------------------------------------

 

SECTION 4 - Attic Areas and Roof Framing
A. Items to be inspected:

1. Framing

2. Ventilation

3. Insulation

 

B. The Inspector is not required to:

1. Inspect mechanical attic ventilation systems or components

2. Determine the composition or energy rating of insulation materials

3. Move insulation.

​​

--------------------------------------------

 

SECTION 5 - Plumbing

A. Items to be inspected:

1. Water supply piping

2. Drain, waste, and vent piping

3. Faucets and fixtures

4. Fuel gas piping

5. Water heaters

6. Functional flow and functional drainage

 

B. The Inspector is not required to:

1. Fill any fixture with water, inspect overflow drains or drain-stops, or evaluate backflow devices, waste ejectors, sump pumps, or drain line cleanouts 

2. Inspect or evaluate water temperature balancing devices, temperature fluctuation, time to obtain hot water, water circulation, or solar heating systems or components

3. Inspect whirlpool baths, steam showers, or sauna systems or components

4. Determine the existence or condition of polybutylene, polyethylene, or similar plastic plumbing.

5. Inspect fuel tanks or determine if the fuel gas system is free of leaks

6. Inspect wells or water treatment systems.

​​

---------------------------------------------

 

SECTION 6 - Electrical

A.   Items to be inspected:

1. Service equipment

2. Electrical panels

3. Circuit wiring

4. Switches, receptacles, outlets, and lighting fixtures

 

B.   The Inspector is not required to:

1. Operate circuit breakers or circuit interrupters

2. Remove covers or dead fronts

3. Determine the accuracy of any such labeling within the circuit panel

4. Inspect de-icing systems or components

5. Inspect private or emergency electrical supply systems or components

​​

---------------------------------------------

 

SECTION 7 - Heating and Cooling

A. Items to be inspected:

1. Heating equipment

2. Central cooling equipment

3. Energy source and connections

4. Combustion air and exhaust vent systems

5. Condensate drainage

6. Conditioned air distribution systems

 

B. The Inspector is not required to:

1. Inspect heat exchangers or electric heating elements

2. Inspect non-central air conditioning units or evaporative coolers

3. Inspect radiant, solar, hydronic, or geothermal systems or components

4. Determine volume, uniformity, temperature, airflow, balance, or leakage of any air distribution system

5. Inspect electronic air filtering or humidity control systems or components

6. Inspect or determine thermostat calibration

​​

---------------------------------------------

 

SECTION 8 - Fireplaces and Chimneys

A. Items to be inspected:

• Chimney exterior

• Spark arrestor

• Firebox

• Damper

• Hearth extension

 

B. The Inspector is not required to:

1. Inspect chimney interiors

2. Inspect fireplace inserts, seals, or gaskets

3. Operate any fireplace or determine if a fireplace can be safely used.

​​

--------------------------------------------

 

SECTION 9 - Building Interior

A. Items to be inspected:

1. Walls, ceilings, and floors

2. Doors and windows

3. Stairways, handrails, and guardrails

4. Permanently installed cabinets

5. Permanently installed cook-tops, mechanical range vents, ovens, dishwashers, and food waste disposals

6. Absence of smoke and carbon monoxide alarms

7. Vehicle doors and openers

 

B. The Inspector is not required to:

1. Inspect window, door, or floor coverings

2. Determine whether a building is secure from unauthorized entry

3. Operate, test or determine the type of smoke or carbon monoxide alarms or test vehicle door safety devices

4. Use a ladder to inspect systems or components

5. Inspect microwave ovens or test leakage from microwave ovens.

6. Inspect or determine appliance calibration.

​​

============================

​

Part III. Limitations, Exceptions, and Exclusions

 

A. The following are excluded from a real estate inspection:

1. Systems or components of a building, or portions thereof, which are not readily accessible, not permanently installed, or not inspected due to circumstances beyond the control of the Inspector or which the Client has agreed or specified are not to be inspected

2. Site improvements or amenities, including, but not limited to; accessory buildings, fences, planters, landscaping, irrigation, swimming pools, spas, ponds, waterfalls, fountains or their components or accessories

3. Auxiliary features of appliances beyond the appliance’s basic function

4. Systems or components, or portions thereof, which are under ground, under water, or where the Inspector must come into contact with water

5. Common areas as defined in California Civil Code section 1351, et seq., and any dwelling unit systems or components located in common areas

6. Determining compliance with manufacturers’ installation guidelines or specifications, building codes, accessibility standards, conservation or energy standards, regulations, ordinances, covenants, or other restrictions

7. Determining adequacy, insurability, efficiency, suitability, quality, age, or remaining life of any building, system, or component, or marketability or advisability of purchase

8. Structural, architectural, geological, environmental, hydrological, land surveying, or soils-related examinations

9. Acoustical or other nuisance characteristics of any system or component of a building, complex, adjoining property, or neighborhood

10. Conditions related to animals, insects, or other organisms, including fungus and mold, and any hazardous, illegal, or controlled substance, or the damage or health risks arising there from including but not limited to lead paint, asbestos or toxic drywall.

11.  Risks associated with events or conditions of nature including, but not limited to; geological, seismic, wildfire, and flood

12. Water testing any building, system, or component or determine leakage in shower pans, pools, spas, or any body of water

13. Determining the integrity of hermetic seals at multi-pane glazing

14. Differentiating between original construction or subsequent additions or modifications

15. Reviewing information from any third-party, including but not limited to; product defects, recalls, or similar notices

16. Specifying repairs/replacement procedures or estimating cost to correct

17. Communication, computer, security, or low-voltage systems and remote, timer, sensor, or similarly controlled systems or components

18. Fire extinguishing and suppression systems and components or determining fire resistive qualities of materials or assemblies

19. Elevators, lifts, and dumbwaiters

20. Lighting pilot lights or activating or operating any system, component, or appliance that is shut down, unsafe to operate, or does not respond to normal user controls

21. Operating shutoff valves or shutting down any system or component

22. Dismantling any system, structure or component or removing access panels other than those provided for homeowner maintenance

 

B. The Inspector may, at his or her discretion:

1. Inspect any building, system, component, appliance, or improvement not included or otherwise excluded by these Standards of Practice. Any such inspection shall comply with all other provisions of these Standards.

2. Include photographs in the written report or take photographs for Inspector’s reference without inclusion in the written report. Photographs may not be used in lieu of written documentation.

 

​